Rottler SG80MTS

MANUALMATIC Heavy Duty Cylinder Head Seat & Guide Machine




Machine Operations

  • Seat & Guide Machining

  • Applicable Industries

  • Cylinder Head Shop
  • Diesel Rebuilder
  • Earth Moving
  • Heavy Duty
  • Large Engine
  • Locomotive Engine
  • Marine Workboat
  • Oil & Gas
  • Power Generation
  • Remanufacturing
  • Tractor Pulling

  • PDF Resources

    SG80MTS Brochure
    SG Pilot Catalog
    SG80MTS Optional Equipment Catalog
    SG Optional Equipment Catalog
    SG Inserts & Profiles Catalog

    The Rottler SG80 series were created specifically for machine shops
    that rebuild small to large cylinder heads found in the heavy duty engine
    industry. Large cylinder heads come in many shapes and sizes, from 24 valve
    single casting cylinder heads to huge single cylinder heads used in natural
    gas, mining and marine workboat engines. We put our trusted engine block
    machining technology to work designing a heavy duty machine that handles many
    operations required on a wide variety of cylinder heads.



    At Rottler we believed that many large cylinder heads could be "plunge
    cut" with fixed tooling to save time and money. We realized that plunge
    cutting would require a very rigid machine utilizing many of our already
    established design features such as Rottler's exclusive spindle design.



    Over the decades, Rottler's spindle design has proven that our engine block
    machines are able to "plunge cut" wide counterbores found in large
    engine blocks with exceptional results. We used this spindle design for the
    SG80MTS and it has since been proven that the SG80MTS is
    capable of plunge cutting large valve seats very quickly and with excellent
    CONCEN and surface finish.

    The machine has 2 modes of operation:

    1. MANUALMATIC – a brand new concept has been added to these machines which should increase productivity by 30-50%. During seat cutting, the operator does not have to operate any buttons or switches, simply turn the spindle feed steering wheel up and down and the control takes care of all the functions like workhead float/clamp, pilot centering in the valve guide and spindle on/off. When depth of seat is reached, the control automatically changes spindle RPM to high/finish speed to give equal depth of every seat and consistent surface finish results.
    2. MANUAL – the buttons on touch screen are the same as the previous SGM machines. There is no external dial gage, the spindle vertical position is displayed on the touch screen. Simply feed the spindle down until the cutting insert touches the valve seat, touch set zero button and then the digital display will show exactly where the spindle is at all times. The change from low to high/finishing speed is easier as there are 2 separate buttons. The foot pedal for clamp and float of workhead has been eliminated and now controlled on touch screen for manual and automatically for MANUALMATIC.





    For more information: See the SG80MTS Brochure or give us a call at +1
    (253) 872-7050

    Proven Rottler Spindle Design -
    The large diameter precision spindle nut has an R40 taper with the Quick Change Self Locking Spindle Nut System. Tooling never comes loose and no wrenches are required to change tools. Rottlers unique Heavy Duty tooling allows large and wide Valve Seats to be machined to accurate Concentricity. Solid Carbide Pilots offer maximum rigidity and long lifefor years of precision machine work.

    UNIPILOT Tooling -
    The UNIPILOT tooling system allows the carbide centralizing UNIPILOT to work like a live pilot. It stays in the spindle while moving from valve guide to valve guide, but all at the same time has a fixed pilot design to give improved concen. See brochure for more information.

    360 Degree Roll Over Fixture -
    Rottler's 360 Degree Roll Over Fixture comes standard on the SG80A. The fixture allows large 24 valve cylinder heads to be clamped with reference to their head gasket fire deck and rolled 360 degrees in one set up. The heavy duty clamping and fine adjust system allow quick leveling and rigid clamping for heavy cutting during machining. (Optional)

    Adjustable Air Float and Air Clamp Work Table -
    The large worktable of the SG80A consists of two 68" (1730mm) long parallels that are mounted on an air floating and air clamping base. These extra long T-slot parallels allow a wide variety of fixtures and jobs to be set up for machining. The complete table and fixture assembly is easily adjusted in/out with air float and locked rigidly with air clamping allowing cylinder heads with four valves per cylinder to be adjusted in/out and machined without resetting of the cylinder head in the fixture. Just press the foot pedal to float the table, slide in or out and the table locks in position ready for machining.
    MANUALMATIC Touch Screen Control allows valve seats to be cut to equal depth without the operator looking at dials or gages. The LED lights flash when the preset depth is reached.Machine Work Head Floats on Air Cushion for Precision Centering  - Total Travel in In/Out Direction 2.5" (678mm) and Left/Right Direction 42" 1067mmSpindle Diameter 3.75" (94mm) Hardened and Ground with 10" (250mm) of Hand Wheel Vertical TravelSteering Wheel for Rapid and Fine Feed Mechanism for Precise Spindle Down FeedHeavy Duty Spindle with Inner Precision Angular Contact Bearings supported in Adjustable Outer BearingsSpindle Rotation by 5HP (4KW) AC Motor with Vector Control - Infinitely Variable to 500RPMDigital Electronic Level for Quick, precise alignment of Fixed Carbide Pilots Complete with Digital electronic level pick-up (out side mount)Spindle Head Tilt - 10 Degrees to left and rightRottler Automatic Tightening and Quick Release Spindle Lock Nut System for One Hand Operation for fitting and removing tooling to and from the spindleTable Cross Slide operated by Foot Pedal with Air Float for Easy Adjustment for In/Out Positioning of the Fixture - Total Travel 6.5" 170mmTooling Storage Cabinet and Mounting Arm and swivels 360-degreesRemovable center tray for Chip DisposalBuilt In Vacuum Tester including Hose, Hose holding Bracket, Filter and selection of pads2 LED Work lightsPaint Color Code: RAL9002 (Grey White)Electrical requirements: 208-240, 30A, 50/60Hz, 1Ph                                               Shipping weight 5,000 lbs. (2,273 kg)Shipping dimensions: 54 X 81 X 90" H (1372 X 2057 X 2286mm H)                                      Prices (US Funds) FOB - EXW, Kent, Washington, USA
    SG80MTS Machine Specifications American Metric
    ControlManual
    Touch Screen12"305mm
    Machine Weight5000 lbs2273 kg
    Spindle - TaperR40 Quick Change with Automatic Lock
    Spindle - Diameter3.75"95mm
    Spindle - Rotation Speed40 to 500 RPM
    Spindle - Motor5 HP3.75 Kw
    Valve Seat Diameter Range0.550"-8.25"14-210mm
    Valve Guide Diameter Range0.160"-1.5"4-38mm
    Cylinder Head Dimensions (with 360 degree rollover fixture)49L x 14W x 10H"1250L x 355W x 254Hmm
    Cylinder Head Dimensions (with Parallels)UnlimitedL x 16W x 12 & 14.5H"UnlimitedL x 406W x 340 & 370Hmm
    Spindle Travel/Stroke Vertical10"254mm
    Workhead Travel Horizontal - Airfloat/Airclamp44"1120mm
    Workhead Travel In/Out - Airfloat/Airclamp2.312"58mm
    Workhead Tilt (either side of vertical zero)10 Degrees
    Worktable Travel In/Out - Airfloat/Airclamp7.5"190mm
    Maximum Distance from Parallels to Spindle 29"736mm
    Dimensions - Machine47D x 69W x 83" H 1194D x 1753W x 2108mm H
    Dimensions - Shipping54D x 81W x 90" H 1372D x 2057W x 2286mm H
    Electrical Requirements208-240V, 30A, 50/60Hz, 1Ph
    Air Requirements15 cfm @ 90 psi400 l/min @ 6 bar
    Paint Color CodeRAL9002 (Grey White)